AFK SS316 Gas Safety Stainless Steel Pressure Relief Valve 1/4inch 3/8inch 1/2inch

AFK Stainless Steel 1/4inch 3/8inch 1/2inch Gas Safety Valve Pressure relief valve

Application of Safety Valve Pressure relief valve

The RVH and RV series safety valves are proportional leaked valves. When the pressure rises, it gradually opens, so they do not have a capacity level when the given pressure rises (cumulative), and they do not check according to ASME or any other standards. Some system applications require a security valve to meet special security criteria, so system designers and users must determine when to apply these security standards and whether these security valves meet the safety standards.

operate
■ When the system pressure reaches the set pressure, the safety valve is turned on, and the system pressure falls to below the set pressure.
■ Safety valve selection and installation covers the need to set the pressure to set pressure, and put the corresponding label on the cap cover.
■ For valves that have not been used for a period of time, the initial pressure of the initial loading may be higher than the set pressure.
■ Set pressure and re -seal pressure
Setting pressure is the upstream pressure when there is a fluid for the first time. At room temperature, after the initial load is completed, the set pressure of each valve can be repeated within the range of ± 5 %.
The sealed pressure is the upstream pressure when the flowing body flows out, and the sealed pressure is always lower than the set pressure

test
Each series of proportion of load -unloading valves must be tested by setting performance and re -sealing performance.

Back pressure
■ High pressure valve (RVH)
Through the design of these high -voltage valves, the impact of the system back pressure is minimized.
■ Low pressure valve (RV)
The back pressure of the system will increase the set pressure of the valve. In order to compensate, subtract the results from 0.8 and subtract the results obtained from the required setting pressure.
When the back pressure is equal to atmospheric pressure, the results obtained by the application are preset.
For example: the set pressure required is 120 PSIG. The back pressure of the system is 40 PSIG.
Step 1. Back pressure is multiplied by 0.8.40 PSIG X 0.8 = 32 PSIG.
Step 2. Subtract the result from the required setting pressure. 120 PSIG -32 PSIG = 88 PSIG.
Step 3. Preset the proportion of the proportional load valve on 88 PSIG.

RVH series
■ Used for liquid or gas
■ Set the pressure: 7 kinds of spring can be selected, which increases the range of selection of the setting pressure.
■ Inner diameter: 3.6mm
■ Balanced valve stem design, eliminating the effects of back pressure on tidy pressure
■ Work temperature: -23 ℃ to 148 ℃ (-10 ° F to 300 ° F)
■ Adjustable valve cap, adjustable and setting pressure
■ Anti -pine holes can effectively maintain the setting of settings
■ Various sealing materials are available
■ Label label the range of the whole pressure
■ When the setting pressure is lower than 1500PSIG
Control the handle, this handle can open the valve without changing the setting pressure
■ Conncetion size:
1/4 "to 1/2", 6 to 12 mm dual card sets
1/4 "to 1/2" thread
RV series
■ Used for liquid or gas
■ Set pressure: 10 to 60psig (0.68 to 3.9bar)
■ Inner diameter: 4.0mm
■ Preset pressure = required pressure -0.8* Back pressure
■ Work temperature: -23 ℃ to 148 ℃ (-10 ° F to 300 ° F)
■ Adjustable valve cap, adjustable and setting pressure
■ Anti -pine holes can effectively maintain the setting of settings
■ Various sealing materials are available
■ Label label the range of opening pressure
■ When the setting pressure is lower than 1500PSig, you can choose an artificial super -pitch control handle.
This handle can open the valve without changing the whole pressure
■ Interface size:
1/8 "to 1/2", 3mm to 12mm dual card set
1/4 "to 1/2" thread

RVH-SS-MN4-FN4-A-B

FAQ

Q1. What products can you provide?

Re: Compression fittings(connections), hydraulic fittings, tube fittings, ball valves, needle valves etc.

Q2. Can you make the products based on our requests, such as size, connection, thread, shape and so on?

Re: Yes, We have experienced techincal team and can design and produce the products according to your requirements.

Q3. What about the quality and price?

Re: Quality is very good. Price is not low but pretty reasonable at this quality level.

Q4. Can you provide samples to test? For free?

Re: Of course, you can take several to test firstly. Your side shall bear the cost due to its high value.

Q5. Can you operate OEM orders?

Re: Yes, OEM is supported though we also have our own brand named AFK.

Q6. What payment methods for chose?

Re: For small order, 100% Paypal, Western Union and T/T in advance. For bulk purchase, 50%T/T, Western Union, L/C as deposit, and 50% balance paid before shipment.

Q7. How about the lead time?

Re: Usually, delivery time is 5-7 working days for sample, 7-10 working days for mass production.

Q8. How will you ship the goods?

Re: For small amount, international express is used mostly such as DHL, FedEx, UPS, TNT. For large amount, by air or by sea. Besides, you also can have your own forwarder pick up the goods and arrange the shipment.